EML Array – JBL Components Line Array Package – 28 Cabinets + Fly Bars

EML Line Array in used but working condition.

This complete set contains:

• 28 EML Array Cabinet with transport dolly
• 2x Fly frame and couplers (More available on request)
  NOTE: Amplifiers available on request

Introduction and application:

The Eml array is a 3-way active designed line array element.
It is designed to deliver high-quality reinforcement of music and speech in a variety of applications including concert audio and corporate A/V presentations of all types.

Product placement :

The EML-Array differs from line source line array designs (like Adamson Line Array ) in such way that due to the fact that the EML array uses wave formers instead of waveguides their is more vertical dispersion . We measured a 10° vertical dispersion . This means that the Eml array will work better in situations where vertical dispersion is needed.  It will work best with angles between cabinets , so ideal for Delay , Out fill , large theaters etc..  In all situations where a line source line array (like Adamson ) is less efficient since their vertical dispersion is max 5°.
The EML-array will work less efficient with small or zero angles between cabinets , so it is less suitable for large flat venues,( where line source line arrays perform better.)
Since the low end is horn loaded and extended to 60 Hz , a minimum of sub is required for stand alone applications. When used as delay or out fill , no extra subs are needed.

In a stacked configuration, the Eml array will fit exactly on a S318 sub. The rigging points are designed to connect under a S318 .
Each EML-Array element has an impedance of 8 ohm, this means that we will need one (Ex HLA) top amp rack for 4 elements.
In clusters we will set the limit for 8 cabinets deep maximum, rigging and frames are calculated for 12 deep ,but since it is not a real long throw design we will not use many 0° angles.

Specifications: (One element)

• Freq response: 60 Hz – 16 KHz
• Horizontal Coverage (-6 db ) 90° ,250° – 16Khz
• Vertical Coverage (-6db ) 8° max single element , array dependant for multiple elements.
• Signal Processing : Apex IX special preset
• Recommended X-over points: 60Hz -225Hz, 225Hz-1Khz , 1khz-20 KHz.
• Maximum peak Output 136 to 146 db @ 1m (Frequency / band pass dependent )
• Low Frequency 2 x 2254HPL 14″ Neodymium Differential Drive (600W per driver )
• Band pass sensivity 99 db 1W / 1M
• Nominal Impedance 8 Ohms, wired parallel
• Mid Frequency 2 x JBL 2251HPL 10″ Neodymium Differential Drive (388W per driver)
• Band pass sensivity 102 db 1W/1M with compression plates.
• Nominal Impedance 8 Ohms, wired parallel
• High Frequency:  2 x JBL 2451J 4″ Titanium Diaphragm,1,5″ Throat diameter. (150 W per driver )
• Band pass sensivity 118 db 1W/1M
• Nominal Impedance 8 Ohms, wired parallel
• Input connector Speacon NL8.
  1 = NC 3 = MF
  2 = LF 4 = HF
• Dimensions ( H x W x D ):  382 x 1280 x 565 mm (303mm back)
• Net weight:  72 kg
• Wheel dolly:  10 kg

Note : This product can compete with other array designs like Vertec and EAW and EV etc but since EML has always predict (and proven ) that we need real line source line array systems ,
for long throw applications , we will keep up with that philosophy and only use the Eml -array for productions where it is designed for. Outfilln, Delay, Large theaters , Stacked with a minimum of 3 elements per side.

The rigging system is integrated in the EML-array. Sidebars are used to link two cabinets where the back rigging sets the angles between the cabinets in 9 positions (From 0° to 8° max ) with quick release pins. The wheel dolly is attached to the front through two metal cylinders and locked with two quick release pins